Noticias e historias


image image   







Contact Information:              

Terex Cranes Global Marketing

Press & Public Relations





Building One of Chile’s largest wind farms in just 3 months


Calama, Chile, April16th, 2014 - Wind energy has come a long way in Chile since the first wind farm was inaugurated in 2001, the “Alto Baguales”, a three turbine farm that generated 2 MW of energy. Today, Chile has over 300 MW of wind power generation capacity, and the recently inaugurated “Valle De Los Vientos” park at the northern Chilean region of Antofagasta accounts for 90 MW. “Valle De Los Vientos” is the first of three wind farms planned for this region. With the other two already approved, the Calama joint wind park will have 240 MW capacity and a total investment of more than US$ 500 million. To erect this new generation wind park, developer Enel GreenPower requested lifting services of Gruas Burger and their Terex® CC 2800-1 NT crawler crane.


Erecting wind turbines is somewhat a dichotomy: one has to build the turbines where there is wind, but one can seldom perform lifts with strong wind speeds. Complicating the matter even more is the fact that one has to take into consideration the wind sail area when lifting large surface components. If all this comes together, the window to perform the lifts might be small, and lift companies must be ready to act when it opens. When building an entire wind park comprised of 45 turbines, these variables add up and can bog down a project or significantly increase its costs.


Gruas Burger came to prominence worldwide relative recently for being the crane rental company that supplied the cranes to rescue the 33 miners trapped at a mine in the north of Chile. Not only has this crane and transport company been around since 1996, but it also is no stranger to the hostile climatic conditions of the Chilean Desert, where hot temperatures and high altitudes are everyday working conditions. It was natural that they were the right company to erect a large wind park in the north of Chile.

Planning and erecting a wind park has its idiosyncrasies. Besides transporting the turbines, building the foundations and erecting them, an often overlooked aspect for this type of project is site preparation. Access roads, lifting pads, and support facilities need to be built from scratch, often in remote areas like this one. On top of this, the variability in climatic conditions when the turbines can be erected meant that the project has a high potential for delays and cost increases. To mitigate these risks, it was important to be efficient in planning, and be reliable when lifting.


Efficiency in ground preparation


“Ground preparation is very important when performing lifts, and it’s an aspect one should never skimp on, but there are ways to minimize costs in projects like this,” said Raul Burger, President & Owner, Gruas Burger. “We are very experienced in erecting wind turbines, so we offered the developing company our services with the NT crane so they only needed to build 5.5 m wide roads for the crane instead of 10 m, which is usually needed for a crawler crane. We helped them save a significant amount of money.”

Whereas the track footprint of the conventional Terex CC 2800-1 crawler crane measures over 32 ft (9 m), the track width of the Terex CC 2800-1 NT is only 17.4 ft (5.3 m), allowing Burger’s crews to navigate the narrow roads. Even with the narrow tracks, the crane still offers the high lift capacities customers expect from a 660 US ton (600 tonne) crane. Large 16.4 ft long x 4.6 ft wide (5 x 1.4 m) front/rear outrigger pads work in conjunction with two hydraulically operated 9.8 x 7.9 ft (3 x 2.4 m) side outrigger pads to give the stability required for lifting heavy loads.


Heart stopping construction pace


The pace at which this wind park was built was outstanding by any standards as Raul Burger said: “It was a logistic masterpiece we are proud of. After the access roads and pads were prepared, and the turbine parts in place, we erected each turbine and then crawled with the fully erected crane to the next pad. On average we erected one turbine per day and each turbine required seven lifts. It was indeed a very fast pace!”

The “Valle De Los Vientos” park comprises of 45 Vestas V100/2000 2 MW turbines with a rotor diameter of 100 m. To erect these type of turbines, the crane had to lift loads up to 100 t up to 80 m in height with a usual working radius of 18 m.

“After 2 months of hard work, we lifted the last nacelle. It was a wonderful feeling to look back and see how much we contributed towards renewable power in Chile in such a short time,” concluded Raul.


About the Terex® CC 2800-1 NT crawler crane


The Terex® CC 2800-1 NT crawler crane offers a high return on investment and is among the most economical and versatile narrow track cranes in the 660 US ton (600 tonne) class. Using a selection of specially designed accessories, the crane is convertible from standard (CC 2800-1) heavy lift configuration to a narrow track crane (CC 2800-1 NT) and back, providing outstanding performance in a wide variety of applications, including wind farm sites, where extra heavy load capacity is a necessity.


Recognizing the high potential of the on shore wind turbine market and the subsequent need for dedicated equipment in the 660 US ton (600 tonne) class, Terex Cranes developed the CC 2800-1 NT (narrow track) crane model from the standard CC 2800-1 version to suit specific wind farm construction requirements. Equipped with its narrow track chassis, the Terex CC 2800-1 NT crawler crane can be driven from one construction site to the next, even when access is tight, while fully rigged with counterweights, 334.6 ft (102 m) main boom and LF 2 fixed jib, saving precious time and increasing productivity.


The CC 2800-1 NT version is based on a conventional CC 2800-1 crawler crane, where the standard chassis (27.6 ft {8.4 m} track width) is replaced with the Narrow Track Kit comprising of: chassis track with 5.3 m outer track width and front and rear outriggers, two 16.4 ft long x 4.6 ft wide (5 x 1.4 m) outrigger pads for both front and rear outriggers, two side outriggers with 9.8 x 7.9 ft (3 x 2.4 m) outrigger pads, counterweight suspension frame to lower the center of gravity and control system with remote control unit and full color graphic display monitor at the rear of the crane chassis. To provide stability and quick rigging times, both front and rear outrigger beams remain connected to the carrier.


About Gruas Burger

Gruas Burger is a Chilean company that specializes in lifting and specialized transport. Founded by Raul Burger sen. in 1996, it is today run by Raul Burger jun. the company has 130 team members, 35 cranes with capacities between 25 and 600 tonnes and a full fleet of trailers and tractors with capacities for loads up to 100 t & 45 m in length. With its team members as their most valuable asset, Burger invests continuously in training and development of its team members, not only to keep raising the bar in terms of operational excellence, but also to allow them to progress and pursue further education.



About Terex

Terex Corporation is a diversified global manufacturer of a broad range of equipment that is focused on delivering reliable, customer-driven solutions for many applications, including the construction, infrastructure, quarrying, mining, shipping, transportation, refining, energy, utility and manufacturing industries. Terex reports in five business segments: Aerial Work Platforms; Construction; Cranes; Material Handling & Port Solutions; and Materials Processing. Terex offers financial products and services to assist in the acquisition of equipment through Terex Financial Services. More information can be found at




<< Noticias e historias